800-706-7009

 

Home • Up • 63 Series • 70 Series • CM Communications • DC/Telecom • F3 Telecom • FC / FCA Battery Charger • TD Series, UPS Battery Charger • LC Battery Charger

 

 

Contact Us Toll Free

Buy batteries on-line

Request Info

UPS Systems

Universal Battery Valve Regulated Lead Acid Batteries Batteries

  Emergency Lighting

Battery chargers, rectifiers, dc power systems by SENS Battery Chargers

Click for more about the Battery Rack™ 20 with Tester (Grey) Battery Storage

Specials!

Service

Lease Info

 

 

SENS battery chargers, rectifiers, dc powerBattery chargers, rectifiers, dc power, Battery chargers, rectifiers, dc power, Battery chargers, rectifiers, dc power, Battery chargers, rectifiers, dc power

CM

Communications Battery Charger/Rectifier

 

Space-Saving Telecom Power.

bulletHigh-density design - saves rack space.
bulletIntegral distribution panel - offers 6 fused circuits and low-volt load disconnect.
bullet115/230 VAC, 50/60 Hz input - operates nearly anywhere in the world.
bulletComprehensive alarm system - provides complete status on charger and battery.
bulletHeavy-gauge aluminum housing - gives modern appearance and corrosion protection.

Battery Charger/Rectifier Product Highlights


CM Battery Charger / Rectifier SENS CM chargers/rectifiers supply reliable, efficient DC power to telecommunications equipment, including cellular and point-to-point microwave.

Designed for 19" rack mounting, SENS CM chargers/rectifiers are ideal for space-restricted applications. They consume only 3 rack units and need no space above or below for cooling. An optional distribution panel and low-volt load disconnect are integrated into the charger further reducing the need for rack space.

SENS CM chargers/rectifiers improve user and facility safety, as AC and DC voltages are shielded from accidental contact by hands or tools. Selection of 115 or 230 volts AC is via rear panel switch. 50/60 Hz operation is standard.

An AC input cord is standard. DC output is through a polarity-protected, snap-in connector with positive lock or the integrated distribution panel. Connection to the multi-function alarm system's voltage-free contacts is made through a terminal block on the rear panel.

SENS CM chargers/rectifiers are in use worldwide and have proven to be highly reliable.

 

Battery Charger/Rectifier Specifications

Input Frequency & Voltage Range
50/60 Hz, +5%; 115/230 volt switch selectable, +10%.

Output Voltage
12, 24, & 48 volts nominal. Factory adjusted to approximately 114% above nominal for battery charging. Field adjustable to nominal voltage for power supply use.

Output Voltage Regulation
+1% from no load to full load with simultaneous variations in input voltage of 10% and frequency of 5%.

Current Limiting & Overload Protection
 

bulletSoft start - ensures smooth start up.
bulletElectronically power limited.
bulletAC & DC fuses.

Output Ripple & Noise
30 mV maximum ripple and 32 dBrnC voice-band noise when connected to a battery having capacity in AH four times the ampere output rating of the charger. 100 mV rms maximum with battery disconnected.

Parallel Operation
Chargers can be operated in parallel for redundancy. Chargers share load when set up with a unit of similar current rating. Blocking diode is standard.

Ambient
Operating temperature: -10 C to +50 C.
Humidity: 5% to 95% non-condensing.

Indicators
Alarm indicators and remote contacts. (See Alarm Systems Table.)

Input Connection
AC cord (NEMA 5-15P plug standard); 6' (1.8 meters) in length.

Output Connection
 

bulletModel suffix-A410: Single output via polarity-protected, snap-in connector with positive lock. Output cord with mating connector included. 10' (3 meters) length.
bulletModel suffix-A4A0: 6-circuit distribution panel (GMT fuses; 5A standard, 10A max per circuit and 25A total) with low-volt load disconnect. Compression connections up to #12 AWG.

Chargers / Rectifiers Reverse View

Battery Charger / Rectifier Alarms

 

Mechanical
Housing material: Heavy-gauge, clear-anodized aluminum.
Configuration: 19" relay rack mounting (23" brackets optional).

Rectifier dimensions

 

Charger connector
Rectifier dimensions

Battery Charger/Rectifier Optional Features
 

bulletDC ammeter and voltmeter, 3.5" (89mm) scale, 2% accuracy.
bulletFungus proofing of circuit boards.
bulletExport packaging.
bulletAdapter brackets for 23" rack mounting.
bulletInput and output connections through barrier-type terminal block.

 

How to Order CM Battery Charger/Rectifier
 

  1. Determine standard charger model number. Refer to the Ordering Information Table.
  2. Specify options as line items.

 

Home - 9 Power Problems - Problems with Power - APC - Powerware - MinuteMan - MGE - Liebert - Batteries - Chargers / Rectifiers - Emergency Lighting - Service - Factory Links

 Contact Us

Power Factor Inc.

2526 Manana Dr – Suite 102 – Dallas – Texas – 75220

NO DISSATISFIED CUSTOMERS!

Since 1995

While every precaution has been taken to ensure accuracy and completeness in this literature, Power Factor Inc. assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Specifications subject to change without notice.
All names referred to are trademarks or registered trademarks of their respective owners.